Shareware Overload Trio 2/Shareware Overload Trio Volume 2 (Chestnut CD-ROM).ISO/dir24/aprs308.zip/README.APR

Text File | 1993-12-13 | 18KB | 284 lines

                  AUTOMATIC PACKET REPORTING SYSTEM (APRS)

     APRS is the result of my experience over the last 13 years with trying
to use packet radio for real-time communications or public service events.
Packet radio has great potential but so far has been best used for passing
large volumes of message traffic from point to point or into the national
distribution system.  It has been difficult to apply packet to real time
events where information has a very short life time.  Typically, several
steps are involved in preparing and passing message traffic including
decisions about routing and connectivity.

     APRS avoids the complexity and limitations of trying to maintain a
connected network.  It permits any number of stations to participate and
exchanges data just like voice users would on a single voice net.  Any
station that has information to contribute simply transmits it, and all
stations receive it and log it.  Secondly, APRS recognizes that one of the
greatest real-time needs at any special event or emergency is the tracking of
key assets.  Where is the Event Leader?  Where are the emergency vehicles?
Where is the head of the parade?  Where are the VIP's?  Where is the mobile
ATV camera?  Where are the mobiles?  Included on the distribution disk are
several README text files on specific applications of APRS such as for
weather nets, direction finding, plotting satellite contacts, and so forth.

APRS accomplishes the real-time display of operational traffic via
UI frame broadcasts and map displays.  There are three major display
subsystems and a number of other minor displays as follows:

     LATEST BEACONS - This display maintains a list of the latest UI frame
received from each station.  In effect, this is a multi-station one-line
broadcast message system.  Since the lines contain the LATEST time of receipt,
this display shows if a station is still on line within the last few minutes.

     POSITIONS - This display maintains a separate list of the positions of
each station.  Each position report can also contain a brief comment.  These
lines show the latest time of receiving a given position report and give an
indication of the latency in the network over unreliable paths such as HF.
They also contain Beam Heading for Direction Finding, and Weather conditions
for weather reporting stations.

     MAPS - Maps to any scale from .5 miles up to 2000 miles can be
displayed. Stations are instantly displayed when they transmit a properly
formatted position beacon.  Stations with a reported course and speed are
automatically dead-reckoned to their present position.  You can center the
map anywhere in the world.

     MESSAGES -  In addition to the BEACON text which is used to broadcast
information to all other stations on the net, there is an operator-to-operator
message capability.  Any station can send a one line message to any other
station.  On receipt, the messages are acknowledged and displayed on the
bottom of the receiving stations screen until the operator hits the K key to
kill them.  These messages are ideal for station-to-station comms while
remaining within the APRS environment.  However, they are not as effecient as
the connected protocol, and should not be used routinely for Rag-Chewing on
a busy APRS net.

     ALL TRAFFIC LOG - This display is a time sequenced log of every new
beacon or one line message sent.  Beacons are logged the first time they are
received.  This is in contrast to the LATEST display which shows the most
recent time of receipt of a beacon text.

     WHEN-HEARD - This display maintains a count of the total number of
transmissions from each station per hour.  These statistics are ideal for
displaying the connectivity of the network over varying paths, such as HF, or
to see when stations enter and leave the net.

     DIGIPEATER LIST - This display displays the full raw packet header so that
APRS users can see what digipeater paths are being used by other stations.
The proper use of digipeaters is important in an APRS network.

STATION TRACKING.  Although APRS automatically tracks mobile packet stations
interfaced to GPS or LORAN navigation, the graphic capability of the maps works
perfectly well with manual tracking or with GridSquares.  Any station on HF or
VHF that includes his GridSquare in brackets as the first text in his beacon
text will be plotted by APRS.  Additionally, any station can place an
object on his map including himself and within seconds that object appears on
all other station displays. In the example of a parade, as each checkpoint with
packet comes on line, its position is instantly displayed to all in the net.
Whenever a station moves, he just updates his position on his map and that
movement is transmitted to all other stations.  To track other event assets,
only one packet operator needs to monitor voice traffic to hear where things
are.  As he maintains the positions and movements of all assets on his screen,
all other displays running APRS software display the same displays.  With
version 3.04, there is a Tracking command on the P display that will cause APRS
to keep the map display always centered on a seslected object.

GRID SQUARES:  As of version 2.05, APRS now also plots stations by gridsquares.
Since four-digit grid squares only locate a station to the nearest 60 miles
or so, and six-digit gridsquares only specify stations to the nearest 3 miles
or so, APRS will not display stations reported via gridsquares on map ranges
less than 128 and 8 miles respectively.  Stations reported by grid squares
will each be assigned an exact LAT/LON which is offset from the center of the
grid acording to an algorithm based on the letters of their callsigns.  This
prevents all stations in the same grid square from all being displayed on one
spot in the center and spreads them out in the grid.  The resulting POSIT in
the POSITION list is annotated to indicate that the position is approximate.
Another advantage of GridSquare reporting in APRS is that it allows cautious
people to participate in APRS without revealing their exact location.

USING DUMB TERMINALS IN AN APRS NETWORK:  The simplicity and usefulness
of this geographic capability cannot be over stressed.  Stations running APRS
simply move the cursor to where they think they are on the screen and their
LAT/LONG coordinates are automatically transmitted to all other stations.
Even the simplest of portable packet stations with dumb terminals can report
their positions if a pre-printed map is made available to all net
participants which has a LAT/LONG grid reference.  The portable station just
looks at the map and enters his LAT/LONG into his beacon text.  Using the
same map, he can plot with pins the location of all other stations as he sees
their position reports go by.  Beginning with version 2.05, APRS also plots
station positions based on Grid Squares.  Eventually, we hope that all stations,
no matter how they are using their TNC, will include their LAT/LONG or Grid
Square in their Beacon Text so that their location is immediately available.
See the file README.DUM for details on APRS formats and help in using dumb
terminals in an APRS network.

SPACE APPLICATIONS:  APRS could be a solution to the effective use of orbiting
terrestrial style packet radio digipeaters in space such as on the Shuttle, MIR,
AO-21 and ARSENE.  The problem with space digipeaters is the saturation on the
uplink channel which makes the use of a normal CONNECTED protocol impractical.
For a CONNECTED contact, a total of five successive and successful packet
transmissions are required.  Not only does APRS reduce this to one packet, but
it also capitalizes on the most fascinating aspect of the amateur radio hobby,
and that is the display on a map of the location of those stations.  If all
stations were encouraged to simply insert their LAT/LONG or Grid Square as the
first characters of their beacon text, everyone within the satellite footprint
would see the location of every successful uplink.  Since the shuttle is a
rapidly moving object, the locations of successful uplink stations will move
progressively along the ground track.  All it would take to implement this
capability is a single AMSAT news bulletin to ask all stations to insert their
POSITS in their beacon text.  No changes onboard the shuttle or MIR would be
required.  See README.SAT for further details.

FOX HUNTING OR DIRECTION FINDING:  APRS is an excellent tool for plotting the
location of a hidden transmitter, balloon, or interfering signal.  The  X
command (cross fiX) has been added to permit displaying the intersection of
bearing lines from a number of reporting stations.  To use APRS in this manner,
each station having a bearing report on the direction of the target, simply
enters that bearing using the ctrl-B command.  His station will then not only
report his location, but also a line of bearing.  All stations running APRS
can simply hit the X key to display the intersection of these bearing lines.
Further, if a DF vehicle has a GPS or LORAN-C device on board, he can be
tracked and directed right to the location of the target.  As of APRS version
3.00, there is an optional Dopler DF interface for automatically plotting and
transmitting instantaneous DF bearings.  Please note that APRS uses 360 degrees
for North and 000 to indicate that no direction information is available.  For
more info on direction finding with APRS, see the README.DF file.

WEATHER STATION REPORTING:  APRS position reports can also include the wind
speed and direction, as well as other important weather conditions.  As of
version 2.07, APRS supports an optional serial interface to the ULTIMETER-II
home weather station.  With this interface, your station includes WX conditions
in your position report for display at all other stations in the network.  All
weather stations show up as a bright blue circle, with a line indicating wind
speed and direction.  Remember that APRS uses 360 degrees for North and uses
000 to indicate that no wind direction is available.  Each of these stations
can be highlighted in turn with a single key stroke, so that all WX reports
across the state can be had at a glance.  See README.WX for more information.

PROTOCOL - Since the objective of APRS is the rapid dissemmination of real-time
information using packet UI frames, a fundamental precept is that old
information is less important than new information.  All beacons, position
reports, messages and display graphics are redundantly transmitted but at a
longer and longer repition rate.  Each new beacon is transmitted immediately,
then 20 seconds later.  After every transmission, the period is doubled.  After
ten minutes only six packets have been transmitted.  After an hour this results
in only 3 more beacons; and only 3 more for the rest of the day!  All trans-
missions cease if the CTRL-X command is used.  But a transmission can be forced
at any time by hitting the T key.  In version 2.13, the initial start up
beacons and position reports are started at a ten minute interval in order
to reduce QRM, since these beacons usually do not contain any new information.
Once changed, of course, they will be handled as any new information and sent
frequently for the first few minutes.  For details on the APRS raw packet
formats see the README.DUM file.

COMMANDS:   In most cases the keyboard is always active.  There is a mneumonic
relationship between all functions and the appropriate key.  For this reason,
the PC function keys are avoided.  (APRS processing of packets on the air is
continuous EXCEPT while waiting for the user response to a prompt.  These
prompts are surrounded with a blue box).  The most useful commands are:

  Space Key           - Display map and all station locations
  H - Help            - Two alternating pages of help
  V - Validation      - Information on registering and Validating your copy
  L - Latest beacons  - Displays the latest BText from each station
  P - Positions       - Displays a list of all stations reporting positions
  C - Controls        - Display a one line status of all control states
  W - When heard      - Displays the number of beacons per hour per station
  D - Digis Used      - Displays the digipeater paths being used by others
  S - Send            - Send a directed message to a station
  Alt-F   Features    - Cities, Leaders, Tags, Roads or waterways on/off
  Ctrl-L  Load file   - Loads a previously saved file and screen location
  Ctrl-S  Save file   - Saves all positions and Beacons for later restart
  alt-R   Replay      - Replay the recent movements of stations in memory
                        or replay a track history file
  Ctrl-V  Via digi    - Used to change your VIA path for outgoing packets

DEMONSTRATION FILE:  To see how the APRS system works on an ordinary packet
traffic frequency, use ctrl-L to load the file called FREQ505.BK.  This file
contains all the local stations on 145.05 MHz in our area.  To see the tracking
of the GPS equiped Army/Navy game football run, load the file named FBALL.BK
and replay the file named FBALL.HST and select to see only FBALL, or CHASE1.
To see the marathon event we just completed, load MARTHON.BK and replay the
MARTHON.HST file.  See Details in README.1st.

HOOKING STATIONS:  The yellow circular cursor can be moved to select any
station in the system using the arrow keys.  On the MAP display move the
cursor near any station symbol.  Then hit the RETURN key to "hook" the
station.  Detail information on that station will be displayed in the upper
left hand corner.  Alternatively, use the gray + and - keys to step through
each station one by one.  Once hooked, several functions may be performed:

     1.  LIST BEACONS - hitting the L key will list all beacons from that
     station currently in memory.

     2.  POSITION CORRECTION - performed by moving the cursor to the
     desired new location and pressing the Insert key.  You are then
     prompted to enter in a new course, speed, comments or time as needed.

     3.  DELETE - performed by hitting the Del key.  Removes the station
     from the position file.

     4.  ALARM - you can set an alarm on a station which will alert you if that
     station ever moves its position.

     5.  TRACK - will cause APRS to always center display on selected station

The hook function also works on the LATEST and POSITION display lists by
using the up/down arrow keys.  If a position exists, you are given the
opportunity to display the map screen with that station centered on the
display.  This is useful for finding a station which is far off the currently
displayed map range.  If a position does not exist, you are given the
opportunity to create one.

REPLAY:  Since all beacons and position reports are retained, the alt-R key
may be used to replay the positions of a moving station.  The replay is
performed either from active memory, or from historical files.  HISTORY files
are automatically saved whenever the memory is full.  Use the C command to
toggle on and off the display of callsigns, and use the R command to Re-center
the map display if the mobile station moves off the screen.  During replay,
use these single key commands:

      C    - CALLsigns on/off
      HOME - Homes map to presently displayed station
      F    - Faster.  Speeds up playback
      P    - Pause
      S    - Slow.  Slows down playback
      Q    - Quit playback.
      PgUp/PgDn - Zoom in and out


FILES:  There are several files used by the system:

  MAPLIST .map - Contains a list of all map files to be used and also the
                 default LAT/LONG, Range and GMT offset for your location
  USA     .map - large scale map of the USA
  SSxxxxxx.map - Maps of any area to any scale.  Usually the first 2 chars
                 indicate the state.  APRS can only handle 60 maps.
  TKxxxxxx.HST - Track history.  The day and time that the file was saved
                 is indicated by the x's. If the file contains an interesting
                 trip or station movement for later replay, the file should
                 be renamed using DOS to a more descriptive *.HST file
  BACKUP  .BK  - Automatic backup of system every time program is quit.  This
                 file is overwritten every time the program is quit.  The
                 alt-L command will reload this file with one key stroke.
  BKxxxxxx.BK  - Backup file of the latest beacons and POSITS heard created
                 whenever Ctrl-S save is commanded.  Usually used to save a
                 file backup of a special event or situation.
  BLxxxxxx.LOG - Log of all new beacons received in chronological order of
                 first receipt.  A good log of text used during an event.


CHESSBOARD:  To demonstrate the flexibility of APRS in reporting the movement
of objects on screens in a net, I have drawn a chessboard map in the center
of the Gulf of Mexico.  Any two stations can play chess easily using APRS by
placing pieces on the map using the alt-A key and updating their positions
using the cursor and INSert keys!  As a start, I have already loaded all the
pieces and saved them in CHESS.BK.  To move a piece, first enable it for
uplinking using the X key on the P screen.  Then move the cursor and hit the
INSert key.  So once the other station sees you move, it is a good idea to
Quit the uplinking of that piece using the Q key on the P-list to minimize
channel traffic.  Monitoring stations that have also loaded the CHESS.BK file
will see the game progress too!  You should consider going to an unused
frequency so as not to clutter an active APRS net.